BETOFROST P150 The admixture is produced as a 40 % concentration solution in accordance with TU BY 191604636.001-2012. The admixture is intended for use in the production of heavy-weight concrete at ambient temperatures down to -15 °C. |
Printed format and Technical Certificate
BETOFROST P150
BETOFROST P150
ADMIXTURE PROPERTIES
For the construction of cast-in-place and precast-monolithic concrete and reinforced concrete structures and buildings. For the manufacture of precast concrete and reinforced concrete products at construction sites and casting yards.
APPLICATION OF THE ADMIXTURE
BETOFROST P150 admixture is applied in the construction of cast-in-place concrete and reinforced concrete structures, in the manufacture of precast concrete and reinforced concrete products at casting yards and construction sites, and for the preparation of mortars within the temperature range of 0 °C to -15 °C.
During the preparation of concrete mixes in winter periods, compliance with the requirements of SNiP 3.03.01-87 is mandatory.
The admixture is recommended for use at ambient air temperatures ranging from 0 °C to -15 °C.
ADMIXTURE PROPERTIES
BETOFROST P150 admixture does not reduce the pot life of the mix, does not alter the color of the concrete, and does not cause efflorescence on the surface.
USAGE
The use of BETOFROST P150 admixture reduces the amount of mixing water by 10-20 % from the initial value.
When used as a Group I efficiency plasticizer, the minimum dosage of the admixture must be 0.9 % by weight of cement, calculated as dry matter.
The effectiveness of the admixture is maximized when introduced together with the mixing water.
ADMIXTURE DOSAGE
The recommended dosage of BETOFROST P150 admixture is 0.6-1.5 % by weight of cement, calculated as dry matter.
The dosage depends on the forecasted minimum ambient air temperature.
*– The dosage is specified for an average heavy-weight concrete composition with a cement content of 400 kg/m3 and a water-cement ratio of 0.4.
The admixture contains no chlorides, is suitable for use in reinforced and prestressed structures, and does not induce reinforcement corrosion.
The dosage depends on the concrete mix design, product type, and structural features of the component (Consult with our specialists).
THIS INFORMATION IS FOR REFERENCE PURPOSES. PRODUCT TESTING UNDER PRODUCTION CONDITIONS IS REQUIRED FOR ADMIXTURE IMPLEMENTATION.
APPLICATION OF THE ADMIXTURE
BETOFROST P150 admixture is applied in the construction of cast-in-place concrete and reinforced concrete structures, in the manufacture of precast concrete and reinforced concrete products at casting yards and construction sites, and for the preparation of mortars within the temperature range of 0 °C to -15 °C.
During the preparation of concrete mixes in winter periods, compliance with the requirements of SNiP 3.03.01-87 is mandatory.
The admixture is recommended for use at ambient air temperatures ranging from 0 °C to -15 °C.
ADMIXTURE PROPERTIES
BETOFROST P150 admixture does not reduce the pot life of the mix, does not alter the color of the concrete, and does not cause efflorescence on the surface.
USAGE
The use of BETOFROST P150 admixture reduces the amount of mixing water by 10-20 % from the initial value.
When used as a Group I efficiency plasticizer, the minimum dosage of the admixture must be 0.9 % by weight of cement, calculated as dry matter.
The effectiveness of the admixture is maximized when introduced together with the mixing water.
ADMIXTURE DOSAGE
The recommended dosage of BETOFROST P150 admixture is 0.6-1.5 % by weight of cement, calculated as dry matter.
The dosage depends on the forecasted minimum ambient air temperature.
Design minimum concrete curing temperature, °C | Additive dosage, % by mass of cement, calculated on a dry basis*** |
0 ÷ -5°С | 0,6-0,9% |
-5 ÷ -10°С | 0,9-1,2% |
-10 ÷ -15°С | 1,2-1,5% |
*– The dosage is specified for an average heavy-weight concrete composition with a cement content of 400 kg/m3 and a water-cement ratio of 0.4.
The admixture contains no chlorides, is suitable for use in reinforced and prestressed structures, and does not induce reinforcement corrosion.
The dosage depends on the concrete mix design, product type, and structural features of the component (Consult with our specialists).
THIS INFORMATION IS FOR REFERENCE PURPOSES. PRODUCT TESTING UNDER PRODUCTION CONDITIONS IS REQUIRED FOR ADMIXTURE IMPLEMENTATION.
OCCUPATIONAL HEALTH AND SAFETY
The admixture is classified as a low-hazard substance (Hazard Class IV according to GOST 12.1.007-86) regarding its effect on the human body.
During application, sanitary and hygienic requirements must be observed; personal protective equipment must be used to prevent direct contact with the skin and eyes.
Drinking, eating, and smoking are prohibited when handling the admixture.
PACKAGING, TRANSPORTATION, AND STORAGE
The admixture is classified as a low-hazard substance (Hazard Class IV according to GOST 12.1.007-86) regarding its effect on the human body.
During application, sanitary and hygienic requirements must be observed; personal protective equipment must be used to prevent direct contact with the skin and eyes.
Drinking, eating, and smoking are prohibited when handling the admixture.
PACKAGING, TRANSPORTATION, AND STORAGE
- The liquid admixture is supplied in bulk into the buyer's clean plastic or metal containers of various capacities.
- The admixture is transported by any means of transport in accordance with cargo transportation regulations.
- The admixture shall be stored in enclosed premises at positive temperatures in hermetically sealed containers.
- The admixture may be stored in enclosed premises down to -15 °C in hermetically sealed containers.
- The admixture must be protected from direct sunlight, heating above 50 °C, and freezing.
- The shelf life is 12 months from the date of manufacture.
- The admixture is a non-flammable liquid.
© ПОЛИСТРОЙХИМ - ЧАСТНОЕ ТОРГОВО-ПРОИЗВОДСТВЕННОЕ УНИТАРНОЕ ПРЕДПРИЯТИЕ УНП 191604636, ОКПО 380484815000
Head Office:
Belarus, Minsk, 23 Uruchskaya St., Office 402B
Multi-line:
+375 (17) 51-25-911
Belarus, Minsk, 23 Uruchskaya St., Office 402B
Multi-line:
+375 (17) 51-25-911
